本文图片、文字由上海淞江集团橡胶膨胀节http://www.shnxxjjt。。ｃｏｍ/xjpzj/提供。有疑问请
上海淞江减震器集团专业生产销售橡胶接头，橡胶软连接，橡胶柔性接头，橡胶避震喉,橡胶膨胀节,橡胶补偿器等,产品品种齐全,质量稳定,国内外。
怎么安装橡胶接头才能防止开裂？
想要防止橡胶接头的开裂，我们在平时的使用中就要留意对其进行保护，按照以下的操纵步骤就可以了，我们就会减少断裂的事件发生。
*，链接部位的强度比较低，那么如果是胶接方法不准确，接头的强度就会更加低，有可能会出 现开裂.
第二，使用的过程中所链接的长度不够，强行超出链接长度，随意扩大收缩范围也有可能开裂.
第三，安装好后，在管道其它地方随意拉带此处超出伸缩范围，也有可能开裂.
第四，在户外恶劣天气的影响下，爆晒等，低于使用温度也有可能开裂。
第五，在制作硫化过程中所用橡胶橡胶机能不好或已经自硫失效、打磨过度、钢丝绳生锈等，接头部位的强度将会大打折扣，在使用时，也会有可能轻易泛起接头部位断开的现象。
当我们用机械方式橡胶接头连接时，接头强度仅能达到带体强度的百分之四十至百分之五十，冷胶方式质量比较好时，接头强度能达到百分之六十至百分之七十，而热胶接头强度能达到百分之八十至百分之九十，要确保接头方法准确、无质量缺陷.
所以我们在安装橡胶接头的时候要正确安装。不要强制安装。
The picture and text provided by the Shanghai Songjiang group shockproof rubber connector http://www.shnxxjjt。。ｃｏｍ/. Have questions, please contact
Shanghai Songjiang absorber group professional production and sales of rubber joints, rubber soft connection, flexible rubber joint, shock absorber rubber hose, rubber expansion joint, rubber compensator, product variety is complete, stable quality, best-selling domestic.
How to install rubber joints to prevent cracking?
To prevent cracking of rubber joints, we should pay attention to the use of the usual protection, in accordance with the following control steps can be, we will reduce the occurrence of the fault.
First, the strength of the link site is relatively low, so if it is a plastic connection method is not accurate, the strength of the joint will be even lower, there may be cracking.
Second, the use of the process of the length of the link is not enough, forced out of the link length, free to expand the scope of the contract also has the potential to crack.
Third, after installation, in other places free here beyond the extension range of pipe strap, there may be cracking.
Fourth, under the influence of adverse weather conditions, such as the sun, the temperature is also lower than the use of cracking.
Fifth, in making vulcanization process for rubber and its function is not good or have since sulfur failure, polished excessive, wire rope, such as rust, the strength of joints will be greatly reduced, when in use, could easily thrown joints off phenomenon.
When we use mechanical rubber joints, joint strength can only achieved with a 50 percent to 40 percent of the body strength, cold glue quality is good, the strength of the joint can reach 70 percent to 60 per cent, and hot glue joint strength can reach 90 percent ten to eight percent, to ensure the joint method is accurate, no quality defects.
So we need to install the rubber connector correctly. Don't force the installation.
