污水处理设备 污泥处理设备 水处理过滤器 软化水设备/除盐设备 纯净水设备 消毒设备|加药设备 供水/储水/集水/排水/辅助 水处理膜 过滤器滤芯 水处理滤料 水处理剂 水处理填料 其它水处理设备
东莞市超顺机电设备工程有限公司
东莞市超顺机电设备工程有限公司
小鱼干包装机小鱼干包装机--刚性真空封口机有旋盖封口机、滚边封口机、滚纹封口机、压塞封口机、压盖封口机、卷边封口机等
小鱼干包装机
小鱼干包装机--刚性真空封口机有旋盖封口机、滚边封口机、滚纹封口机、压塞封口机、压盖封口机、卷边封口机等。不一样的封口机可以结束不一样类型商品的封口，跟着真空封口机品种的增多，在工作中的运用也越来越广泛。在封口机运用进程中经常会碰到这样那样的缺陷，下面超顺设备小鱼干包装机为你扫盲真空封口机运用进程中常见的缺陷。
（1）封口不牢，发生缺陷的缘由是冷压胶轮压力不合适，热封速度过快，热封温度缺乏，热封薄膜质量有问题，遇到这种状况可适当提高热封温度，再降低热封速度，一起加大冷压胶轮的压力。
（2）温度表闪现失灵，封口温度失控，热封温度不稳定，封口处不是被烧焦，就是封合不牢，封口变形，很丑陋，构成该缺陷首要缘由是温度计已坏，有必要修补；别的，热电耦可以也坏了，不能正常地将感应温度传至温度计上。换上同类型、同标准的热电耦即可。
（3）封口机走走停停，速度不一致，构成缺陷的缘由首要是电动机的轴杆联接处与变速箱联接处呈现掉落、松懈表象，从头紧固螺丝，使之悉数符合，问题也就处理了。
（4）封口处呈现不规则痕纹及气泡，此类缺陷较为常见，首要是因为冷压胶轮上有摆放不规则的凹凸痕迹，直接反映到包装上，使封口处呈现较多的显着痕纹，设备运用时刻长了，高温带上附着了尘埃及塑料屑等脏物，构成高温带不光滑、不平坦，使得封口受热不均匀，经冷压轮压合后呈现气泡。交流冷压胶轮，清洗或从头交流高温带即可打扫。
搜索关键词：小鱼干包装机
Small fish dry packing machine
Small fish, dry rigid vacuum packaging machine, sealing machine screw cap sealer, flange sealing machine, rolling machine, pressure sealing machine, capping, edge sealing machine, etc. Different sealing machine can end of the sealing of different types of goods increased with vacuum sealing machine varieties, also more and more extensively used in our work. In sealing machine use process we often encounter this or that kind of defects, the following super paramagnetic equipment dry fish packing machine for literacy vacuum sealing machine you use in the process of common defects.
(1) the sealing not firm, is the cause of the defect of cold pressing roller pressure is not appropriate, heat sealing speed too fast, the lack of heat sealing temperature, heat sealing film quality has a problem, meet this kind of condition can be appropriately raise heat sealing temperature, and then reduce the heat sealing speed, with increasing of cold pressing roller pressure.
(2) the thermometer flash failure, the sealing temperature control, heat sealing temperature is not stable, pincer-like device isn't burned, is not firm sealing, sealing deformation, very ugly, constitute the primary reason for the defects is thermometer is bad, it is necessary to repair; Other, thermoelectric coupling was broken, can not be normally would transmit the induction temperature to the thermometer. Can be changed into the same type, same standard thermocouple.
(3) the machine stops, the speed is not consistent, constitute a defect reason first is the motor shaft rod coupling and transmission connection place appear to drop, lax appearances, fastening screws from the ground up, all conform to, problems are dealt with.
(4) an irregular mark lines and bubble pincer-like device, this kind of defect is common, first because of cold pressing roller are put on irregular concave and convex, directly reflect the packaging, make the pincer-like device presents more significant mark lines, and equipment use time long, high-temperature belt and plastic scraps on the dust dirt, a thermal zone not smooth, not smooth, makes the sealing heat unevenly, after cold pressing wheel pressing the air bubbles. Exchange of cold pressing roller, clean or communication from thermal belt can be clean.
Search keywords: fish dry packing machine
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
环保在线 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
