污水处理设备 污泥处理设备 水处理过滤器 软化水设备/除盐设备 纯净水设备 消毒设备|加药设备 供水/储水/集水/排水/辅助 水处理膜 过滤器滤芯 水处理滤料 水处理剂 水处理填料 其它水处理设备
深圳市乐买宜电子有限公司
深圳市乐买宜电子有限公司
中国台湾华仪71307100系列耐压测试仪7130产品介绍大尺寸128x64LCD显示器，可完整呈现测试结果，提高判读效率；体积小、重量轻(10kg)，，适合简易高压测试应用
中国台湾华仪 系列 耐压测试仪
7130 产品介绍
大尺寸128 x 64 LCD 显示器，可完整呈现测试结果，提高判读效率；体积小、重量轻 (10kg)，，适合简易高压测试应用。7100 系列提供多台联机同步测试功能，亦可透过远程控制 (RS-485 或PLC 远程控制接口)，满足自动化测试，提高生产效率。
7130 产品特点
直流耐压测试具有 Discharge 直流高压快速放电装置，避免被测物上残余电压，造成人员触电危险
Smart GFI 智慧防高压触电线路 (169000)，随时侦测回路，杜绝触电伤害，保障人员安全
可进行多达100台联机控制，同时输出，快速测试
搭配7314 接地阻抗测试器，可同时进行耐压及接地测试，缩短测试时间
开机智能检测功能，自动确认仪器输出正常，确保测试的可靠度
校正及预警时间设定功能，提醒用户定期校正，确保测试质量
键盘锁定 (Key Lock) 功能，保护记忆组数据，避免误触按键所造成的危害
三种测试功能可供选择：ACW, DCW, IR
大型128×64 Graphic LCD 显示器
单机可与7315接地阻抗测试器连结符合标准19英吋仪器架
可同时进行100台的联机测试
内建10组程序记忆、每一组3个测试步骤可进行程序记忆步骤的连结测试
快速放电功能，可于0.2秒将被测物上的电能放完，确保人员安全
防高压触电功能，当人体误触时可立即中断输出
开机自我检测功能的测试，可于测试前进行判定各项测试功能是否正常
前面板软件输入校正
时间与日期的设定，可设定校正时间及预警时间提醒使用者
内建PLC Remote遥控界面
键盘锁定功能
安全锁定功能
体积小、重量轻
7100系列 型号选择：
7130 AC Withstａnd VoltageTester |
| |
7132 AC Withstａnd Voltage / Insulation Resistance Tester |
| |
7140 AC/DC Withstａnd Voltage Tester |
| |
7142 AC/DC Withstａnd Voltage / Insulation Resistance Tester |
|
中国台湾华仪 系列 耐压测试仪 技术参数
| SPECIFICATIONS | ||||
| MODEL | 7130 | 7132 | 7140 | 7142 |
| AC WITHSTAND VOLTAGE | ||||
| Output Rating | 5KVAC/20mA | |||
Range | Resolution | Accuracy | ||
| Output Voltage, KVAC | 0-5.00 | 0.01 | ±（2% of setting + 5V） | |
| Output Frequency | 50Hz/60Hz ±100ppm, User Selection | |||
| Output Waveform | Sine Wave ,THD.<2% (Resistive Load), Crest Factor = 1.3 - 1.5 | |||
| Output Regulation | ± (1% of output + 5V), From no load to full load | |||
| SETTINGS | ||||
| Max-Limit AC Current, mA | 0 - 20.00 | 0.01 | ±（2% of setting + 2counts） | |
| Min-Limit AC Current, mA | 0 - 9.999 | 0.001 | ±（2% of setting + 2counts） | |
| Ramp Up Time, second | 0.1 - 999.9 | 0.1 | ±（0.1% + 0.05sec） | |
| Ramp Down Time, second | 0 - 999.9 | 0.1 | ||
| Dwell Time, second | 0, 0.3 - 999.9 (0=continuous) | 0.1 | ||
| Arc Detection | 0, 1 - 9 ranges (0=OFF, 9 is the most sensitivity) | |||
| DC WITHSTAND VOLTAGE (7140,7142 ONLY) | ||||
| Output Rating | 6KVDC/7500μA | |||
| Output Voltage, KVDC | 0 - 6.00 | 0.01 | ±（2% of setting + 5V） | |
| Output Ripple | <5%（6KV/7500μA at Resistive Load） | |||
| SETTINGS | ||||
| Max-Limit DC Current, μA | 0 - 7500 | 1 | ±（2% of setting + 2counts） | |
| Min-Limit DC Current, μA | 0 - 999.9 | 0.1 | ±（2% of setting + 2counts） | |
| Ramp Up Time, second | 0.1 - 999.9 | 0.1 | ±（0.1% + 0.05sec） | |
| Ramp Down Time, second | 0, 1.0 - 999.9 | 0.1 | ||
| Dwell Time, second | 0, 0.4 - 999.9 (0=continuous) | 0.1 | ||
| Arc Detection | 0, 1 - 9 ranges (0=OFF, 9 is the most sensitivity) | |||
| Discharge Time | ≦ 200 msec | |||
| INSULATION RESISTANCE (7132,7142 ONLY) | ||||
| Output Rating | 1KVDC/9999MΩ | |||
| Output Voltage, DCV | 30 - 1000 | 10 | ±（2% of setting + 5V） | |
| SETTINGS | ||||
| Max-Limit Resistance, MΩ | 0, 1 - 9999 (0=OFF) | 1 | ±（2% of setting+2counts）at 500-1000VDC, 1 -1000 MΩ | |
| Min-Limit Resistance, MΩ | 1 - 9999 | 1 | ±（5% of setting+2counts）at 500-1000VDC, 1000 -9999 MΩ | |
| ±（8% of setting+2counts）at 30-500VDC, 1 -1000 MΩ | ||||
| Ramp Up Time, second | 0.1 - 999.9 | 0.1 | ±（0.1% + 0.05sec） | |
| Ramp Down Time, second | 0, 1.0 - 999.9 | 0.1 | ||
| Delay Time, second | 0, 0.5 - 999.9 (0=continuous) | 0.1 | ||
| MEASUREMENT | ||||
| AC/DC Voltage, KV | 0 - 6.00 | 0.01 | ±（1.5% of reading + 1count） | |
| DC Voltage, V (IR only) | 30 - 1000 | 1 | ±（1.5% of reading + 5V） | |
| AC Current, mA | 0 - 3.500 | 0.001 | ±（2% of reading + 2counts） | |
3.00 - 20.00 | 0.01 | |||
| DC Current, μA | 0 - 350.0 | 0.1 | ±（2% of reading + 2counts） | |
| DC Current, mA | 0.300 - 3.500 | 0.001 | ||
3.00 - 7.50 | 0.01 | |||
| Resistance, , MΩ | 1 - 9999 (Auto Range) | 0.001 0.01 0.1 1 | ±（2% of setting+2counts）at 500-1000VDC, 1 -1000 MΩ ±（5% of setting+2counts）at 500-1000VDC, 1000 -9999 MΩ ±（8% of setting+2counts）at 30-500VDC, 1 -1000 MΩ | |
| GENERAL | ||||
| Input Voltage AC | 115/230Vac±15%, 50/60Hz ± 5%, Fuse 3.15A | |||
| PLC Remote Control | Input : Test , Reset , Memory1.2.3 , Interlock | |||
| Output : Pass , Fail , Processing , Reset-Out | ||||
| Interface(Option) | RS485 Interface | |||
| Memory | 10 memories, 3 steps/memory | |||
| Graphic Display | 128×64 Graphic LCD | |||
| Safety | Built-in Smart GFI circuit,GFI trip current 450?A max, HV shut down speed: <1mS | |||
| Key Lock | To prevent unauthorized alteration of the test Parameters | |||
| Calibration | Build-in software and external calibrated meters | |||
| Verification | Build-in software driven verification menu to test fault detection circuits | |||
| Alarm Volume Setting | Range: 0-9 ;0=OFF, 1 is softest volume, 9 is loudest volume. | |||
| Environment | 0-40℃, 20-80%RH | |||
| Dimension/Net Weight | 215mm(W)×89mm(H)×370mm(D)/ 10Kg | |||
| STANDARD ACCESSORIES | ||||
| Power Cord(10A) | ×1 | |||
| Fuses | ×2 (Including a spare contained in the fuse holder) | |||
| Interlock Disable Key(1505) | ×1 | |||
| Hipot Test Lead ,1.5m(1101) | ×1 | |||
| Hipot Return Lead ,1.8m(1102) | ×1 | |||
| *product specifications are subject to change without notice. | ||||
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
环保在线 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
