安全滑触线日常保养事项分析解读

安全滑触线在使用过程中加强维护保养非常重要，不少单位的滑触线系统因失于维护而导致故障频繁，影响正常生产。*，昂立电气滑触线是国内滑触线行业的企业，昂立电气滑触线在国内多个领域市场占有比例遥遥。为了保证滑触线正常运行，延长其使用寿命，其售后服务贾工程师根据多年经验，提出了滑触线日常维护与保养方面的看法：

Security sliding touch line in the use of the process to strengthen the maintenance is very important, sliding contact line system due to the loss of many units to maintain and lead to frequent failures, affecting the normal production. As everyone knows, Jieneng electrical sliding contact line is the sliding contact line industry leader, Jieneng electrical sliding contact line occupies more than in the domestic market share be way ahead. In order to ensure the normal operation of the sliding contact line, prolong the service life of the after sale service, Jia engineer based on years of experience, the sliding contact line daily maintenance and maintenance:

1.连接件：至少每年检查一次。重点检查紧固螺栓、焊缝及支撑件是否松动、锈蚀、移位等，发现问题及时处理。

1 connections: at least once a year to check. Focus on examination of the fastening bolts, welds and support is loose, corrosion, shift, found problems in a timely manner.

2.特别对行车轨道重合度、轨距、倾斜度等偏差较大、使用频繁、车间粉尘过大、温度较高及有水、酸、碱、雾和室外使用的环境，必须加强日常检查与维护。

2 special on the running track of coincidence degree, gauge, inclination, deviation, frequent use, workshop dust is too large, high temperature and water, acid, alkali, fog and outdoor environment, must strengthen the routine inspection and maintenance.

3.安全滑触线集电器：至少每季度检查一次。重点检查紧固件有无松动、移位及塑料件和活动件磨损情况，检查弹簧拉力（集电器电刷与导轨的接触应保持一定压力（见下表）。发现问题及时处理。

The 3 Collector: at least quarterly check once a. Focus on examination of the fastener without loosening, displacement and plastic parts and moving parts wear, check the spring tension (collector brush and rail contact should maintain certain pressure (see table below). Found problems in a timely manner.

4.电刷：应根据移动用电设备使用情况每1—3个月检查一次。重点检查集电器电刷的磨损情况，若磨损量≥5mm时，必须更换。检查时若发现电刷松动或发生磨损偏斜时，应查明原因，及时处理。

4 brush: electric equipment should be based on the use of every 1 - 3 months check once a. Focus on examination of the collector brush wear, if wear is greater than or equal to 5mm, must be replaced. If found loose or worn oblique brush examination, should identify the reasons, timely treatment.

5.日常检查：重点检查轨道的平直度有无明显偏差（大于20mm）、错位，绝缘保护件有无脱落、断裂、破损，不锈钢“v"型槽有无翘起；轨道上有无异物及导电粉尘等。必要时应检测其绝缘电阻是否符合要求（相间绝缘电阻应≥10MΩ）。

5 daily inspection: inspection of rail straightness has no significant deviation (more than 20mm), dislocation, insulation protection piece off, fracture, damage, stainless steel "V" type groove is not tilted orbit; there is no foreign body and conductive dust etc.. When necessary, to detect the insulation resistance is required (interphase insulation resistance should be greater than or equal to 10M.).